Internal Medicine Physician Dr. Carrie Madej: Covid Vaccination

From Unfuck U . . .

I uploaded the whole video before I watched it.
I only knew a shorter version of the clip below.
After I skimmed over the whole interview I found most of what she says about transhumanism very unbelievable. It just doesn’t compute.
So what I did was what the unknown cutter did: I shortened the video to its best part.
Here ya go:

I urge all of you to go to unfucku.com and watch the interviews – I could not figure out how to embed them – the first one is about 5 minutes and is enough on its own – the second one is the full interview – While you are watching this – REMEMBER that the highly accredited DR. GATES has been involved with this assault on humanity for years – I hope you folks have your seat belts on as the ride is just beginning and it’s going to be a rough landing . . .

I have said it before and I will say it again – You CAN trust me on this stuff – Why you ask?? – Because I have the same medical degree that billy boy gates has . . .

Have Fun! – Run the Gun! – and remember – Fish Heads are Cheap!!

Clive Maund – Genocide is their End Game

You really won’t like this – but reality is a bitch . . .

“In a nutshell, they are to cull a large percentage of the human race and to turn the survivors into a completely controlled army of slaves who own nothing and are dictated to and tracked, traced and monitored 24 / 7 everywhere, even inside their own homes, which of course they will no longer own.”

Click on the above to go and read the article – while it’s still out there and not labeled as “subversive”.

The pedocrats are going to get the same thing shoved up their collective asses for the next four years that “We The People” had to put up with for the last four years – the only real difference is we don’t burn down parts of cities – we burn fucking continents down – go ahead and ask the Japanese how that little dust up ended for them . . .

Have Fun! – Run the Run! – and remember – Fish Heads are Cheap!!

GHOSTED: ATF Visiting End Users; Requesting Forfeiture Of Polymer80 Kits

From The Firearm Blog –

Earlier today TFB reported on a story in the Wall Street Journal stating that the ATF had apparently conducted a search warrant at Polymer80 Inc, a company known for producing 80% firearm kits and related parts. These 80% builds, often referred to as “Ghost Guns” by media outlets, presumably because they can be built into firearms without needing to visit an FFL, have long been a topic of debate. This morning, an anonymous TFB reader provided additional information pointing to the ATF visiting end users and requesting the forfeiture of certain Polymer80 kits.

You think the incoming Harris administration meeting with the atf on the 10th of November was productive??

How long before the atf starts searching house to house for drill presses – grinders – files etc.?? Rewards to snitching commie fucks for tips phoned in?? Now I’m wondering if their going to show up looking for these ??

Plumbing supplies? -Verboten! / Common house hold cleaning products – Verboten! / Wrong Speak? – Verboten! / Wrong Think? – Verboten! / Too much red meat in your possession? – Verboten! / Watching the wrong tv shows? – Verboten! / visiting the wrong web sites? – Verboten! / too much money in the bank? – verboten! / No Certificate Of Vaccination IDentification Card? – Verboten!

Wow – Just Fucking Wow . . .

Have Fun! – Run the Gun! – and remember – Fish Heads are Cheap!!

CZ 97BD Issue

I have read on multiple forums about putting a drop of Loctite on the Loaded Chamber Indicator screw – as they have a nasty habit of backing out – then the LCI assembly slides forward and heads to parts unknown – Well . . . I didn’t and It did . . .

Glanced down at the pistol as it was heading from the holster to the night stand and I realized it was missing – oops . . .

So I ordered the LCI “delete plate” from CZCUSTOM.COM – then proceeded to find my itty bitty tube of blue Loctite and patiently awaited the arrival of the part . . .

If you look at the part from the under side – you see a roll pin – you need to either “gently” flatten it with a punch or file it down a tiny bit at a time if it is sticking out too far – you want to achieve an almost interference fit as the plate slides into place . . .

And then just a little Loctite on the threads – BLUE NOT RED – you may want to remove it some day – and start with the smallest METRIC Allan wrench you have – that will more than likely be the right one – I could not find a torque spec for the screw – use common sense – seriously – using Loctite and as tiny as the screw is – think inch pounds of torque – and yes if I could have found spec’s for it I would have used my inch pound torque wrench . . .

Screwed in – snugged down . . .

All the excess Loctite cleaned up – ready to go back in service – the Loctite should set up in about 20 minutes and be completely cured in 24 hours . . .

Have all you folks been nice ? . . . What are you hoping to get from Santa this year??

Have Fun! – Run the Gun! – and remember – Fish Heads are Cheap!!

Oh My My . . .

Image from GunsAmerica

From Sportsmans Warehouse < HERE >

Uberti 1873 Cattleman Ursus 10mm Auto 5.5in Blued Revolver – 6 Rounds

Uberti 1873 Cattleman Ursus 10mm Auto 5.5in Blued Revolver – 6 Rounds – The Uberti Cattleman II with retractable firing pin is a breakthrough for those seeking enhanced safety with regard to original Old West revolvers without sacrificing the visual authenticity of a 1st-generation Colt.

As any cowboy knows, the safest way to carry a single-action is with the hammer resting on an unloaded chamber. This is true even for the Uberti retractable firing pin design. But in the case of the Uberti design, the risk of accidental discharge is reduced: the firing pin is not locked into the firing position unless the trigger is pulled.

This enhanced safety feature is available without a visible transfer bar safety, which those who insist on visual authenticity might not want. In other words, from the outside this revolver’s looks and operation are identical to those of an original.

Now this is something I truly DON’T need – so of course it is on the “to buy” list – LMAO!

I wonder just how hard you could push 180 grain 10mm pills short of Kabooming the cylinder?? 2000 fps??

The biggest question is who can I get to test fire it as the powder load starts creeping from the stupid loadings into the you’re crazed loadings – it might be fun ( right up to where you have a catastrophic failure ) to see what you could achieve – or just shoot it and enjoy it – Buffalo Bore makes some hell for stout 10mm . . .

Shot some Buffalo Bore out of my Glock 20 – it is stout – this would be a real hoot – especially with the porting – I couldn’t find an image of the 10mm I could grab so I used the one from Guns America . . .

Have Fun! – Run the Gun! – and remember – Fish Heads are Cheap!!